# Foam Inserts for Protective Cases: EPE vs EVA vs PU vs CNC

> Which foam type to specify inside a protective case: EPE, EVA, polyurethane pluck foam, layered CNC-cut inserts and anti-static options, with density guidance.

Human-readable page: https://kexinn.org/foam-insert-guide/
Site overview for AI agents: https://kexinn.org/llms.txt

## Page content

DOC **KB-FOM-003**REV 2026-09-21CLASS: PUBLIC

## Foam Inserts for Protective Cases: EPE vs EVA vs PU vs CNC-Cut

Direct answer

EPE is the low-cost general cushioning foam; EVA is firmer and holds precision-cut cavities, making it the standard for layered CNC inserts; open-cell PU is the material of "pluck foam" trays that users tear to shape; anti-static (conductive-dissipative) grades of EPE/EVA/PU protect electronics. For OEM electronics, specify a CNC-cut layered EVA insert with anti-static grade.

## §01The four foam families

| Foam | Feel / density | Best for | Watch out for |
|---|---|---|---|
| EPE | soft, ≈20–35 kg/m³ | general cushioning, void fill, low cost | poor edge definition; ages faster under compression |
| EVA | firm, ≈30–80 kg/m³ | precision CNC cavities, presentation cases | cost; heavier than EPE |
| PU (open-cell) | very soft | pluck-foam trays, lens/equipment wraps | absorbs water if the case floods; crumbles over years |
| Anti-static grades | same as parent foam | PCBs, instruments, any ESD-sensitive load | must be specified at order time — often pink or black conductive |

## §02Layered insert anatomy

A typical OEM insert stacks three or more layers: a thin top "cap" layer for looks, a middle layer with CNC-cut cavities matching the product silhouette, and a dense base layer under the load. Recessed finger notches near each cavity let users remove items one-handed. Edge-glued layers should use contact adhesive compatible with the foam, or heat-lamination for EVA.

## §03How much cavity clearance?

- Allow **2–5 mm** of clearance around the item silhouette for insertion and extraction.
- Compress foam by roughly **20–30 %** of its thickness at rest to hold the load — more than that fatigues the foam, less lets the item migrate.
- Heavy items need the cavity in the **lower half** of the stack so shock loads transfer into the base layer and shell, not into a thin foam bridge.

**Spec tip:** ask your supplier for the foam's compression-set value and thickness tolerance. Two "EVA 40 kg/m³" inserts from different factories can behave very differently after 500 open/close cycles.

## Frequently asked questions

### What is the difference between EPE and EVA foam?

EPE is softer and cheaper, ideal for general cushioning and void fill. EVA is denser and firmer, so it holds a machined cavity edge cleanly — that is why precision inserts are cut from EVA layers.

### Is pluck foam good for professional use?

Pluck (PU) foam is configurable in seconds and fine for hand tools, but it tears at finger holes over time and offers little protection against small movements. For electronics or presentation loads, CNC-cut EVA is more durable and looks professional.

### Do I need anti-static foam?

If the load includes PCBs, sensors or any ESD-sensitive device, yes. Standard foams are insulators and can hold static charge; anti-static or conductive grades dissipate it. Specify it when ordering — it changes the material.

### How thick should case foam be?

A common layout is 10–20 mm lid foam, 30–60 mm cavity layer and 15–30 mm base foam, tuned to item weight and fragility. Fragile instruments need more lid and base cushioning than rugged tools.

## Related guides

[KB-MAT-002PP vs ABS vs Rotomolded PE vs Aluminum: Case Materials Compared](https://kexinn.org/case-materials-compared/)[KB-SIZ-004How to Choose the Right Protective Case Size](https://kexinn.org/how-to-size-a-protective-case/)[KB-STD-005Drop and Impact Standards for Protective Cases: MIL-STD-810, ATA 300 and ISTA](https://kexinn.org/drop-and-impact-standards/)

REF KB-FOM-003 · Published 2026-09-21 · Reviewed by the KeXin Materials engineering team · Sources: IEC 60529; ISO 6346; ATA 300; MIL-STD-810; Incoterms® 2020
